In the version with the conveyor or ventilation floor the silo can be used as a cold air dryer: in the Akyurek ventilation silo, grain can be stored with up to 20% moisture content and can be dried by full ventilation combined with "move". The mounted conveyor and ventilation floor can be used for either ventilation or emptying the grain.
spoilage by molds
damage by beetles
can be eaten by rats and mice
may be contaminated by cats
Choose Akyurek grain storage, for your precious crop is threatened by the following factors:
The rectangle silos by Akyurek are available in three versions:
mounted on a hopper (screwed or welded) or
conveyor floor installation
Advantages of Akyurek rectangle silos
the weather risk is reduced because the grain can be stored moist
large quantities can be taken over and are immediately under control
the takeover effectiveness of large quantities guarantees also a busy harvester-use
reduction of work tops - thus lower costs
conservation of the crop for longer time periods at low cost and time taken
high sales proceeds during seasonal fluctuations
exact design - therefore easy and fast assembly
all elements are galvanized - modular system
favorable "price-benefit ratio".
A lot of reasons argue for conveyor-bottom:
The union of ventilation and removal of grain saves conveyors above all at several cells.
The removal by conveyor-bottom is wear-free and handles the grain with care.
plate between bottom and grain:
Through the complete separation of ground and grain, no ground-moisture can reach into the storage-grain.
The ventilation is excellent through the big air-exit-surface. Cooling of the grain through winter-ventilation on 10°C is possible and protects from insects.
storage of grain up to 17% humidity:
Because of the good ventilation of the grain, the grain can be stored up to maximum 17% humidity. With a ventilation of 50 - 100m³ air capacity / h. /m³ you can conserve the grain and prepare storable.
cold air drying:
With an air-performance of the fan from approximately 100-200m³ per hour per m³ grain, a cold-air drying is possible up to maximum 20% grain-humidity. The maximum filling height is 4-5m. You have to attend to work with a low air humidity as possible. With a heater, the air can be heated (max. heating 4°-5°C!). Air heating via a heater reduces the relative air humidity per °C about 5%. For "cold -air-drying" a relative air humidity of approx. 65-70% is enough.
Through the rectangular and quadratic silos, you take advantage of your expensive building optimally. Finally you don´t build your hall in round nature.
Often you can save a lot of material by a clever installation of silo cells, because the first cells build parts of further cells.
You don´t waste money because of higher investment costs, but in the course of time it saves a lot of costs for drying and it is very effective against insects and is environment-friendly. Using a conveyor-bottom saves a lot of time by total emptying and is a great assistance.
Advantages of Akyurek
conveyor bottom in galvanized design:
No hopper necessary
ventilation and emptying all in one.
Also suitable for rape
The height of the ventilation slots on the ventilation sheet metal is approx. 1.2 mm, so also suitable for rape.
Effective air guide shafts
The roof turrets are air guide shafts and direct the air flow to the nozzle sheet metal galvanized fixed to the roof turret.
When emptying, the conus ensure a constant grain-inflow to the ventilation sheet metal and prevent avoiding of grain.
Easy montage and long life expectancy
Simple and secure
The way system (per flow path 1 air damper) guarantees maximum safety and best performance at the complete emptying.
Elements of rectangle silos:
Consisting of trapeze-sheet metal elements, tube legs and stiffening parts.
Possible sheet length:
675 mm, 1000 mm, 1250 mm, 1450 mm, 1500 mm, 1750 mm, 2000 mm, 2225 mm, 2500 mm and 3000 mm.
800 mm or 400 mm.
1600 mm, 1200 mm, 800 mm and 400 mm.
For calculation of the silo-width of the 1st cell you have to add 2x the leg-width, for every further cell each 1x leg-width.
The grain-current when emptying: through the opened outflow-slides the larger-part of the grain flows out independently. The last rest is delivered completely by the conveying-bottom (fan).